Can I use thinset to install wonderboard over concrete? Can I use thinset to install wonderboard over concrete? Installing wonderboard over vinyl. Http:// I show how I install cement board. I reveal the methods I use and provide quite a few good.
Wonder. Board Lite Backer. Board | Custom Building Products. Applicable Standards. American National Standards Institute (ANSI) ANSI A1.
1⁄2' WonderBoard is designed for use as an interior or exterior substrate for ceramic tile, stone, slate, thin-brick veneers.
A1. 18. 9, A1. 08. A1. 18. 4 American National Standards for the Installation of Ceramic Tile ASTM International (ASTM) ASTM C1. ASTM C4. 73 Standard Test Methods for Physical Testing of Gypsum Panel Products. ASTM C6. 27 Standard Test Method for Evaluating Ceramic Floor Tile Installation Systems Using the Robinson- Type Floor Tester. ASTM C9. 47 Standard Test Method for Flexural Properties of Thin- Section Glass- Fiber- Reinforced Concrete (Using Simple Beam With Third- Point Loading)ASTM D1. Standard Test Methods for Evaluating Properties of Wood- Base Fiber and Particle Panel Materials. ASTM D2. 39. 4 Standard Methods for Simulated Service Testing of Wood and Wood- Base Finish Flooring.
ASTM E8. 4 Standard Test Method for Surface Burning Characteristics of Building Materials. National Fire Protection Association (NFPA) NFPA 2. Standard Method of Test of Surface Burning Characteristics of Building Materials. Tile Council of North America (TCNA) TCNA Handbook for Ceramic Tile Installation, TCNA Method EJ1. Health Precautions. This product, when cut, drilled or abraded, produces dust containing free silica, which may cause cancer or delayed lung injury (silicosis) if inhaled. Work outdoors, in a well- ventilated area, or use mechanical ventilation.
Wear safety glasses and a dust mask; in very dusty areas or where airborne dust exceeds PEL, wear a NIOSH/MSHA approved respirator. This product contains one or more chemicals known to the State of California to cause cancer.
At this point, I had finished installing the 1/4' thick WonderBoard cement tile backer in the smaller bathroom. This was the first time I had installed cement tile. WonderBoard® Lite Installation Guide UNDERLAYMENT FOR TILE & STONE WonderBoard® Lite Surface Preparation Coverage Look for this icon on products that qualify for a. Installing Cement Backerboard for Tile in a Shower. Installing cement backerboard is one of the more popular choices for a shower. Fiberboard, wonderboard. Cement Backerboards. Custom's WonderBoard Lite is the ideal backerboard for any project. Have a question? We are here to help; 800-272-8786; Contact Us; Surface Prep. Wonderboard is the brand name for a cement backer board for wet applications, mostly under tile. But why isn't it all that wonderful? WonderBoard® Lite Backerboard Related Products. ASTM C947 Standard Test Method for Flexural Properties of Thin-Section Glass-Fiber-Reinforced Concrete. Installing Cement backerboard walls and floor in the bathroom for ceramic tiles - Duration: 2:27. How to install ceramic tile 403,597 views.
Application of Product. Wood Floors. For the subfloor, securely glue and fasten minimum 5/8" (1. OSB panels (PRP- 1. Floor joists should be spaced a maximum of 1.
Exterior Grade Plywood or OSB subfloor with I- joists spaced a maximum of 1. When setting dimensional stone larger than 1. В subfloor is required.
All plywood or OSB subfloor sheets must be gapped 1/8" (3 mm). Use 1" (2. 5 cm) bond- breaker tape over gaps in the subfloor to prevent gaps from filling with thin- set. Using a 1/4" (6 mm) square- notch trowel, apply a setting bed of polymer- modified mortar to the subfloor. Immediately laminate the Wonder. Board. В® Lite. В to the subfloor, leaving a 1/8" - 3/1.
Stagger joints so they do not line up with underlying substrate joints. While the setting bed mortar is still workable, fasten Wonder. Board. В® Lite every 4"- 6" (1. Around the perimeter of each board, locate fasteners within 1/2"- 1" (1. Fill all joints with polymer- modified mortar.
On all joints and corners, prefill the gap with bonding material; then embed 2" (5 cm) mesh tape and smooth material over the joint and corner. Walls and Ceilings. For wall framing, edges parallel to framing should be continuously supported (typical sleeper studs should be used). Framing for a tub surround or prefabricated shower pan should be plumb and square. Provisions for the sheet membrane pan liner must be made to ensure proper backerboard installation at the interface of the tub or pan flange.
For ceiling framing, the complete ceiling assembly allowable deflection due to dead load should not exceed 1/3. Framing members in the walls and ceiling should not exceed 1.
The weight applied to the walls and ceiling frame, including insulation, backerboard, bonding material and facing material, should not exceed 1. M). Backerboard edges parallel to the framing should be continuously supported. Provide additional blocking, when necessary, to permit proper backerboard attachment and reduce deflection between the joists. Leaving a 1/8"В 3/1.
Wonder. Board. В® Lite panels. Stagger board joints with those of adjacent rows. Fasten the backerboard every 6" (1. It is recommended that blocking be installed between the joists to support the ends of the backerboard. On all joints and corners, prefill the gap with bonding material, and then embed 2" (5 cm) mesh tape and smooth the material over the joint and corner.
A moisture barrier must be installed to protect the wall cavity for wet area installations. Nail or staple 1. Precut Wonder. Board. В® Lite panels and make any necessary cutouts.
Install Wonder. Board. В® Lite, leaving a 1/8"- 3/1. Stagger board joints with those of adjacent rows. Fasten backerboards every 8" (2. At all joints and corners, prefill gaps with polymer- modified mortar, then embed 2" (5 cm) alkali- resistant fiberglass mesh tape and smooth material over joint and corner.
Any shelf, ledge or horizontal surface subjected to water exposure must have a slight downward slope for water runoff. These areas also require proper waterproofing. Apply Red. Gard. В® according to directions. For installation of tile, natural stone or a similar material, comply with ANSI A1. Install according to installation instructions for the corresponding mortar data sheets.